Select SL303 Half Surface Pin and Barrel Continous Hinges

 

Select SL303 Half Surface Pin and Barrel Continous Hinges

The Select SL303 Half Surface Pin and Barrel Continous Hinge is an ANSI/BHMA Grade 1 stainless steel hinge which mounts on door face and frame rabbett. The Select SL303 comes with a tamper-resistant door leaf cover. The Select SL303 is designed for 1-3/4" doors weighing up to 600 lb. The Select SL 303 can be installed on doors with a maximum width of 48".

Some features of the Select SL-303 hinge are -

The Select SL-303 is a fire rated hinge.

The Select SL 303 comes with end caps which are spiral-knurled steel caps which seal the barrel ends to contain hinge pin.

The Select SL303 comes with dust free (medical) bearings.

The Select SL 303 comes with templated hole pattern for easy and fast installation.

Call us today for any questions that you might have on your Select SL-303 hinge. We offer the Select SL303 hinge at extremely attractive prices.

Highlights of the Select SL 303 hinge - 

■ Stainless steel

■ Mounts on door face and frame rabbett

■ Tamper-resistant door leaf cover

■ 1/8" door inset

■ For 1-3/4" doors weighing up to 600 lb.

■ 48" maximum door width

Features of the Select SL303

MATERIAL: 14 gauge 304 stainless steel barrel with 3/16" diameter 304 stainless pin. Long-life nylon medical bearings.

LENGTHS: 79", 83", 85", 95" and 119" lengths standard for nominal door heights. Custom lengths are available.

LOAD/FREQUENCY: For 1-3/4"doors, 48" wide (max.), weighing up to 400 lb. (medium-frequency) without frame or door reinforcement; up to 600 lb. (lowfrequency) without frame or door reinforcement.

FINISH: US32D satin stainless steel (630).

CLOSERS: Conventional overhead surface, concealed sliding arm overhead or floor closers may be used with SELECT hinges. Pivot-type floor closers (with a fixed, conflicting center pivot) must be replaced.

ORDER: Specify hinge length. Screw pack contains 10-24 x 7/8" 410SS Phillips flathead undercut self-drilling Tek® screws, 10 x 1-1/4" 410SS Phillips flathead undercut sheet metal screws, 1/4-20 x 3/4" zinc plated Torx® panhead self-drilling Tek® screws, 8 x 3/4" zinc plated Phillips flathead undercut self-drilling Tek® screws and zinc plated cover clips.

AVAILABLE ELECTRIC PREPS: CTP-AR and CTP-VD.

BHMA CERTIFICATION: SL303 pin & barrel continuous hinges conform to BHMA Standard ANSI/ BHMA A156.26-2006 Grade 1.

Select SL303 Screw Count

Part Number Interchange | Select SL303 Pin and Barrel Concealed Continous Hinges

Select Hinges Product Selection Table

SELECT GEARED HINGES
Full Surface (Click Image Below to Go to Category)	Half Surface (Click Image Below to Go to Category)	Full Mortise/Concealed (Click Image Below to Go to Category)	Half Mortise (Click Image Below to Go to Category)	Swing Clear (Click Image Below to Go to Category)	Wide Throw (Click Image Below to Go to Category)	Toilet Partition (Click Image Below to Go to Category)
SL21SD,SL21HD	SL53HD	SL11SD, SL11HD, SL11LL	SL52HD	SL41HD, SL41LL	SL40HD	SL60/SL62
SL57SD,SL57HD	SL54HD	SL12HD
	SL77HD	SL14SD,SL14HD
		SL18SD,SL18HD,SL18LL
		SL24SD,SL24HD,SL24LL
		SL26LL
		SL27LL
		SL31HD
		SL38SD
		SL44HD
		SL48HD
		SL71HD
		SL84HD, SL84LL

SELECT PIN & BARREL HINGES
Full Surface (Click Image Below to Go to Category)	Half Surface (Click Image Below to Go to Category)	Full Mortise/Concealed (Click Image Below to Go to Category)	Half Mortise (Click Image Below to Go to Category)	Swing Clear (Click Image Below to Go to Category)	Toilet Partition (Click Image Below to Go to Category)
SL302	SL303	SL200	SL306	SL310	SL402TP
SL309		SL300		SL311	SL902TP
		SL305
		SL315
		SL3500