Select SL309 Full Surface Pin and Barrel Continous Hinges

 

Select SL309 Full Surface Pin and Barrel Continous Hinges

The Select SL309 Full Surface Pin and Barrel Continous Hinge is an ANSI/BHMA Grade 1, stainless steel hinge. The Select SL309 hinge has a swing-clear action. The Select SL309 hinge comes with a tamper-resistant door leaf cover. The Select SL309 hinge is built for 1-3/4" doors weighing up to 600 lb. and having maximum door width of 48".

Some of the features of the Select SL 309 are -

The Select SL 309 hinge is available in custom lengths

The Select SL-309 hinge is available in custom finishes

Please call us if you want your Select SL-309 in custom lengths or finishes.

Call us today for any questions that you might have on your Select SL-309 hinge. We offer the Select SL 309 hinge at extremely attractive prices.

Highlights of the Select SL 309 hinge - 

■ Stainless steel

■ Swing-clear action

■ Tamper-resistant door leaf cover

■ 1/8" door inset

■ For 1-3/4" doors weighing up to 600 lb.

■ 48" maximum door width

Features of the Select SL309

MATERIAL: 14 gauge 304 stainless steel barrel with 3/16" diameter 304 stainless pin. Long-life nylon medical bearings.

LENGTHS: 79", 83", 85", 95" and 119" lengths standard for nominal door heights. Custom lengths are available.

LOAD/FREQUENCY: For 1-3/4" doors, 48" wide (max.), weighing up to 400 pounds (medium-frequency) without frame or door reinforcement; up to 600 pounds (low-frequency) without frame or door reinforcement.

FINISH: US32D satin stainless steel (630).

CLOSERS: Conventional overhead surface, concealed sliding arm overhead or floor closers may be used with SELECT hinges. Pivot-type floor closers (with a fixed, conflicting center pivot) must be replaced.

ORDER: Specify hinge length. Screw pack contains 12-24 x 7/8" 410SS Phillips flathead undercut self-drilling Tek® screws, 10 x 1-1/4" 410SS Phillips flathead undercut sheet metal screws, 1/4-20 x 3/4" zinc plated Torx® panhead self-drilling Tek® screws, 8 x 3/4" zinc plated Phillips flathead undercut self-drilling Tek® screws and zinc plated cover clips.

BHMA CERTIFICATION: SL309 pin & barrel continuous hinges conform to BHMA Standard ANSI/BHMA A156.26-2006 Grade 1.

Select SL309 Screw Count

Part Number Interchange | Select SL309 Pin and Barrel Full Surface Continous Hinges

Select Hinges Product Selection Table

SELECT GEARED HINGES
Full Surface (Click Image Below to Go to Category)	Half Surface (Click Image Below to Go to Category)	Full Mortise/Concealed (Click Image Below to Go to Category)	Half Mortise (Click Image Below to Go to Category)	Swing Clear (Click Image Below to Go to Category)	Wide Throw (Click Image Below to Go to Category)	Toilet Partition (Click Image Below to Go to Category)
SL21SD,SL21HD	SL53HD	SL11SD, SL11HD, SL11LL	SL52HD	SL41HD, SL41LL	SL40HD	SL60/SL62
SL57SD,SL57HD	SL54HD	SL12HD
	SL77HD	SL14SD,SL14HD
		SL18SD,SL18HD,SL18LL
		SL24SD,SL24HD,SL24LL
		SL26LL
		SL27LL
		SL31HD
		SL38SD
		SL44HD
		SL48HD
		SL71HD
		SL84HD, SL84LL

SELECT PIN & BARREL HINGES
Full Surface (Click Image Below to Go to Category)	Half Surface (Click Image Below to Go to Category)	Full Mortise/Concealed (Click Image Below to Go to Category)	Half Mortise (Click Image Below to Go to Category)	Swing Clear (Click Image Below to Go to Category)	Toilet Partition (Click Image Below to Go to Category)
SL302	SL303	SL200	SL306	SL310	SL402TP
SL309		SL300		SL311	SL902TP
		SL305
		SL315
		SL3500