Command Access PM300 | Power Booster Module

MODELS

All Models have module equipped with standard connector for Command Access & Von Duprin devices. Also, supplied with each model is a 6’ power lead, 12” retrofit wiring harness & detailed wiring instructions

PM300: Standard model designed to work with 24VDC regulated power supplies

PM300D: Same as PM300 with built-in .5 second delay.

PM300AC: Designed to work with 24VAC & unregulated 24VDC power supplies

PM300ACD: Same as PM300AC with built-in .5 second delay.

FEATURES

• Allows a wire run from the power supply to the exit device of up to 700’ with 18/2 wire (see below)

• PM300 compatible with most 24VDC 1.5A or greater regulated power supplies.

• PM300AC compatible with most 24VAC/VDC 1.5A or greater unfiltered or unregulated power supplies.

• Built high output switch for added power when using Command Access power supplies*

• Solid-state design with high quality components make for years of trouble-free operation

• Built-in safety feature that protects module for over-voltage

• Patented Technology

• No hassle 3-Year Warranty

*High output can only be used with PS1, PS210, PS440, PS5-4, or PS5-6 power supplies. PM300AC can use HO switch with most 24VAC & unregulated 24VDC power supplies

SPECFICATIONS

• PM300 Input Voltage Range: 22-30 VDC Filtered & Regulated Voltage

• PM300AC Input Voltage Range: 20-26 VAC Unfiltered/ 20-26 VDC Unregulated Voltage Tubular 3.5”L x 1.25”W

• Standard Mode: Fuse: Glass - 3.5 to 5A • Resetable - 1.0Amp trip Relay: 5A or greater

• High Output Mode: Fuse: Resetable - 2.0Amp trip, 1.1Amp hold (minimum) Relay: 10A or greater

MAXIMUM WIRE RUNS 

• 700’ with 18ga wire

• 1000’ with 16ga wire

Command Access PM300 | Power Booster Module

The patented Command Access PM300 series power booster module is an interface module that connects between the solenoid circuit of a latch-pullback exit device and the power supply. The PM series modules have been offering a reliable, cost-effective interface solution for exit devices for nearly a decade. The PM300 series modules are available for nearly all exit device applications.

Different uses for this module include the following:

Allows a solenoid-driven exit device to be used with a lower cost power supply - The PM300 provides a local power boost and will work with most 1.5 A or greater, 24VDC, non-switching power supplies, eliminating the need for the expensive “speciality” power supply.

Longer wire runs from the power supply to the exit device – Since the PM300 is located in the exit device the allowable distance between the power supply and the exit device without compromising the performance of the device increases significantly

Gives a needed boost to an anaemic power supply/exit device installation – The anaemic conditions could be due to marginal power supply, minor device binding, too small of gauge wire run, too long of a wire run to name a few. PM300 saves the day.

MODELS

All Models have module equipped with standard connector for Command Access & Von Duprin devices. Also, supplied with each model is a 6’ power lead, 12” retrofit wiring harness & detailed wiring instructions

PM300: Standard model designed to work with 24VDC regulated power supplies

PM300D: Same as PM300 with built-in .5 second delay.

PM300AC: Designed to work with 24VAC & unregulated 24VDC power supplies

PM300ACD: Same as PM300AC with built-in .5 second delay.

FEATURES

• Allows a wire run from the power supply to the exit device of up to 700’ with 18/2 wire (see below)

• PM300 compatible with most 24VDC 1.5A or greater regulated power supplies.

• PM300AC compatible with most 24VAC/VDC 1.5A or greater unfiltered or unregulated power supplies.

• Built high output switch for added power when using Command Access power supplies*

• Solid-state design with high quality components make for years of trouble-free operation

• Built-in safety feature that protects module for over-voltage

• Patented Technology

• No hassle 3-Year Warranty

*High output can only be used with PS1, PS210, PS440, PS5-4, or PS5-6 power supplies. PM300AC can use HO switch with most 24VAC & unregulated 24VDC power supplies

SPECFICATIONS

• PM300 Input Voltage Range: 22-30 VDC Filtered & Regulated Voltage

• PM300AC Input Voltage Range: 20-26 VAC Unfiltered/ 20-26 VDC Unregulated Voltage Tubular 3.5”L x 1.25”W

• Standard Mode: Fuse: Glass - 3.5 to 5A • Resetable - 1.0Amp trip Relay: 5A or greater

• High Output Mode: Fuse: Resetable - 2.0Amp trip, 1.1Amp hold (minimum) Relay: 10A or greater

MAXIMUM WIRE RUNS 

• 700’ with 18ga wire

• 1000’ with 16ga wire