Select SL31 HD Heavy Duty Full Mortise Concealed Hinges

 

Select SL31 HD Heavy Duty Full Mortise Concealed Hinges

The Select SL31 HD is a full mortise concealed hinge, with a short frame leaf that allows for removable stop applications. The Select SL31 HD hinge can be purchased in place of the Pemko SPFMSLF hinge. This Grade 1 hinge has been certified by the US Department of State with its 60 minute certification.

The Select SL31 HD hinge is available with electrification options such as Electric Power Transfer Cutout (EPT), Accessible Through Wire (ATW), Exposed Electric Monitor Switch (EMS), Access Panel (AP) and Removable Panel (RP). Call us at 860-537-1328, if you require electrification options.

Buy the Select SL31 HD Heavy Duty Concealed Geared Continous Hinge from locksandsafes.com at extremely economical prices.

Features

MATERIAL:

Extruded 6063 T6 aluminum alloy with self-lubricating polyester thrust bearings.

LENGTHS:

83"and 95" lengths standard for nominal door heights. Hinges can be cut to shorter lengths. Longer hinges are not available.

LOAD/FREQUENCY RATING:

For 1-3/4" doors. 48" max. door width in 16 gauge hollow metal (min.) or 1/8" aluminum (min.).

Heavy Duty — Tested per BHMA standards. Up to 200 lb. doors (high-frequency) and up to 400 lb. doors (medium-frequency) without frame or door reinforcement; up to 600 lb. doors (low-frequency) with the use of Rivnuts in the frame and door.

FINISHES:

All SL31 hinges are stocked in Clear and Dark Bronze anodized aluminum. Custom anodized or painted finishes are available. Product painted or anodized in the field voids the SELECT hinge warranty.

CLOSERS:

Conventional overhead surface, concealed sliding arm overhead or floor closers may be used with SELECT hinges. Pivot-type floor closers (with a fixed, conflicting center pivot) must be replaced.

ORDER:

Specify length, finish and heavy duty (HD). Also, specify door and frame screw applications. 12-24 x 3/4" self-drilling, thread-forming 410SS Phillips undercut flathead screws are provided as a standard pack unless otherwise specified. Wood and thread-forming screws also available. Security screws optional at extra cost.

AVAILABLE ELECTRIC PREPS:

EPT, ATW, EMS, CMG, AP and RP.

BHMA CERTIFICATION:

SL31HD geared continuous hinges conform to BHMA Standard ANSI/BHMA A156.26-2006 Grade 1.

Part Number Interchange

Select Hinges Product Selection Table

SELECT GEARED HINGES
Full Surface (Click Image Below to Go to Category)	Half Surface (Click Image Below to Go to Category)	Full Mortise/Concealed (Click Image Below to Go to Category)	Half Mortise (Click Image Below to Go to Category)	Swing Clear (Click Image Below to Go to Category)	Wide Throw (Click Image Below to Go to Category)	Toilet Partition (Click Image Below to Go to Category)
SL21SD,SL21HD	SL53HD	SL11SD, SL11HD, SL11LL	SL52HD	SL41HD, SL41LL	SL40HD	SL60/SL62
SL57SD,SL57HD	SL54HD	SL12HD
	SL77HD	SL14SD,SL14HD
		SL18SD,SL18HD,SL18LL
		SL24SD,SL24HD,SL24LL
		SL26LL
		SL27LL
		SL31HD
		SL38SD
		SL44HD
		SL48HD
		SL71HD
		SL84HD, SL84LL

SELECT PIN & BARREL HINGES
Full Surface (Click Image Below to Go to Category)	Half Surface (Click Image Below to Go to Category)	Full Mortise/Concealed (Click Image Below to Go to Category)	Half Mortise (Click Image Below to Go to Category)	Swing Clear (Click Image Below to Go to Category)	Toilet Partition (Click Image Below to Go to Category)
SL302	SL303	SL200	SL306	SL310	SL402TP
SL309		SL300		SL311	SL902TP
		SL305
		SL315
		SL3500